Garden Tractor29/04/2024

How to replace a cutting deck drive belt on a garden tractor

If the cutting deck drive belt on your Husqvarna garden tractor is damaged or slips, it needs to be replaced.

Replacing a cutting deck drive belt on your garden tractor depends on the model of your product.

  1. Remove the cutting deck.
  2. Remove any dirt and grass around the bearing housing, blade pulleys and from the top surface of the cutting deck.
  3. Remove the bolt (A), the washer (B) and the idler pulley (C).
  4. Remove the cutting deck belt (D) from the blade pulley on the cutting deck.
  5. Install the new cutting deck in the opposite sequence. Make sure that the cutting deck belt is in the correct position in all belt pulleys.

    CAUTION: Make sure that the cutting deck belt is not twisted.
  1. Remove the cutting deck.
  2. Remove any dirt and grass around the bearing housing, blade pulleys and from the top surface of the cutting deck.
  3. Remove the bolt (A), the washer (B) and the idler pulley (C).
  4. Remove the cutting deck belt (D) from the blade pulley on the cutting deck.
  5. Install the new cutting deck in the opposite sequence. Make sure that the cutting deck belt is in the correct position in all belt pulleys.

    CAUTION: Make sure that the cutting deck belt is not twisted.
  1. Park the product on a level surface and engage the parking brake.
  2. Put the cutting deck in the lowest position.
  3. Remove any dirt and grass around the mandrels and from the top surface of the cutting deck.
  4. Remove the drive belt (A) from the clutch pulley (B) on the engine shaft.
  5. Remove the drive belt from the mandrel pulleys (C) and the idler pulley (D).
  6. Install the drive belt (A) around the mandrel pulleys.

    CAUTION: Put the drive belt in all the grooves on the cutting deck pulleys correctly. The drive belt can become damaged if it is not installed correctly.
  7. Install the drive belt around the idler pulleys (C).
  8. Install the drive belt around the clutch pulley (D) on the engine shaft.
  9. Put the cutting deck in the transport position.
  1. Park the product on a level surface and engage the parking brake.
  2. Put the cutting deck in the lowest position.
  3. Remove any dirt and grass around the mandrels and from the top surface of the cutting deck.
  4. Remove the drive belt from the clutch pulley (M), mandrel pulley (R) and all idler pulleys (V).
  5. Install the drive belt around both mandrel pulleys (R) and around the idler pulleys (V).
  6. Install the belt on the clutch pulley (M).
    CAUTION: Check that the belt is properly routed in all mower pulley grooves.
  7. Raise the attachment lift lever to the highest position.
  1. Park the product on a level surface and engage the parking brake.
  2. Put the cutting deck in the lowest position.
  3. Remove any dirt and grass around the mandrels and from the top surface of the cutting deck.
  4. Remove the drive belt (A) from the clutch pulley (B) on the engine shaft.
  5. Remove the drive belt from the mandrel pulleys (C) and the idler pulley (D).
  6. Install the drive belt (A) around the mandrel pulleys.

    CAUTION: Put the drive belt in all the grooves on the cutting deck pulleys correctly. The drive belt can become damaged if it is not installed correctly.
    NOTE: You must twist the drive belt by 180° at 2 positions (X) to align with the pulleys. Make sure that the thinner part of the drive belt is in the direction of the groove in each pulley.
  7. Install the drive belt around the idler pulleys (C).
  8. Install the drive belt around the clutch pulley (D) on the engine shaft.
  9. Put the cutting deck in the transport position.
Was this article helpful?
Read more about
maintenancepetrol-poweredcutting deckcutting deck drive beltgarden tractor